oct.2004 pin configuration (top view) mitsubishi semiconductor m81016p/fp/kp octal d-type flip-flop driver with clear description m81016 is octal d-type flip-flop driver by 20-pin package. it has 8 same circuit units which is composed of d-type flip-flop logic circuit and high voltage nchmos output transistor. m81016 has a common direct clear input and a common clock input. features lineup with three packages high breakdown voltage (bv dsx 40v) drain output current (i ds(max) = 200ma) with input protection diodes pin assignment of input-output flow through wide operating temperature range (ta = ?0 to +85 c) application led drive function the common direct clear input and common clock input are connected to every circuit unit by the same way. signal at the d inputs is transferred to y outputs by d-type flip-flops on the positive-going edge of the clock pulse. if clr is set to ?? outputs y1-y8 will be altogether set to ? regardless of d1-d8 and clk. the maximum drain current of an output is 200ma. the maximum between drain-source is 40v. moreover, M81016FP/kp can save space with mini-flat package. logic diagram (positive logic) 1 2 3 4 5 6 7 8 9 10 20 19 18 17 16 15 14 13 12 11 clr d1 d2 d3 d4 d5 d6 d7 d8 clk v dd gnd input output y1 y2 y3 y4 y5 y6 y7 y8 package type 20p4b(p) 20p2n-a(fp) 20p2e-a(kp) d2 3 y2 18 d ck r q d3 4 y3 17 d ck r q d4 5 y4 16 d ck r q d5 6 y5 15 d ck r q d6 7 y6 14 d ck r q d7 8 y7 13 d ck r q d8 9 y8 v dd gnd 12 20 11 d ck r q d1 2 1 10 y1 19 clr clk d ck r q
oct.2004 mitsubishi semiconductor m81016p/fp/kp octal d-type flip-flop driver with clear function table (each channel) h : high level l : low level x : irrelevant output : y input clr l h h h h clk x d x l h x x h h l latched latched l timing diagram supply voltage drain-to-source voltage input voltage drain output current power dissipation operating temperature storage temperature v v v ma w c c 7 0.5 ~ +40 0.5 ~ v dd 200 1.47 1.10 0.68 40 ~ +85 55 ~ +125 ratings symbol parameter conditions unit absolute maximum ratings (unless otherwise noted, ta = ?0 ~ +85 c) v dd v ds v i i ds p d t opr t stg m81016p M81016FP m81016kp recommended operating conditions (unless otherwise noted, ta = ?0 ~ +85 c) v v v v parameter 4.5 0 0.7v dd 0 0 0 0 0 0 0 0 0 20 5 40 limits min typ max symbol unit v dd v ds v ih v il supply voltage drain-to-source voltage h input voltage l input voltage drain output current (current per 1 circuit when 8 circuits are com- ing on simultaneously) 5.0 5.5 40 v dd 0.3v dd 200 135 200 120 200 95 v dd 500 20 i ds duty cycle no more than 45% duty cycle no more than 100% duty cycle no more than 34% duty cycle no more than 100% duty cycle no more than 18% duty cycle no more than 100% v dd = 4.5v v dd = 4.5v v dd = 4.5v v dd = 4.5v v dd = 4.5v conditions v in t r ,t f t su t h t w f p fp kp input voltage rise time, fall time, drain output setup time before clk hold time, data after clk pulse duration clock frequency ma v ns ns ns ns mhz d clr clk y 5v gnd 5v gnd 5v gnd v oh v ol ta = 25 c, when mounted on board output, h current per circuit output, l
oct.2004 mitsubishi semiconductor m81016p/fp/kp octal d-type flip-flop driver with clear 0.002 0.005 0.005 0.005 0.005 0.25 0.51 2.5 40 v (br)dsx i dsx i ih i il v a a a 5 1 ? 5 5 0.38 0.77 3.8 symbol unit parameter test conditions limits min typ max drain-source breakdown voltage drain-source leakage current ??input current ??input current i ds = 1ma v ds = 40v v dd = 5.5v, v i = 5.5v v dd = 5.5v, v i = 0v v dd = 5.5v v i = 5.5v or 0v i ds = 100ma, v dd = 4.5v i ds = 200ma, v dd = 4.5v i ds = 100ma, v dd = 4.5v electrical characteristics (unless otherwise noted, v dd = 5v, ta = 25 c) i cc v ds r ds(on) supply current ??output voltage drain-source on-state resistance a v ? ns ns ns ns 10 3 35 30 symbol unit parameter test conditions limits min typ max low-level to high-level and high-level to low-level output transition time t tlh t thl t plh t phl c l = 30pf (note 1) switching characteristics (v dd = 5v, ta = 25 c) low-level to high-level and high-level to low-level output propagation time (clk) all outputs off all outputs on low-level to high-level output propagation time (clr) t plh(r) 35 ns
oct.2004 mitsubishi semiconductor m81016p/fp/kp octal d-type flip-flop driver with clear timing diagram note 1 test circuit pg r l output c l y clr d gnd v dd v dd v cc clk pg (1) pulse generator (pg) characteristics : prr = 1mhz, duty cycle = 50%, t r = 6ns, t f = 6ns, zo = 50 ? , v i = 5v (2) output conditions : r l = 240 ? , v cc = 24v, v dd = 5v (3) electrostatic capacity c l includes floating capacitance at connections and input capacitance at probes. 50% d clk 50% y 10% 90% 50% 10% 90% t tlh t thl 5v gnd 5v gnd v cc v ol t plh t phl 50% switching times input setup and hold waveforms 50% 50% clk 5v gnd t su d t h t w t r t f 5v 50% 10% 90% 10% 90% gnd 50%
oct.2004 mitsubishi semiconductor m81016p/fp/kp octal d-type flip-flop driver with clear typical characteristics ta=25 c v dd =4.5v 10 1 110 2 2 10 3 357 23 57 23 57 duty cycle-drain current characteristics (m81016p) drain current i ds (ma) 200 q ~ u i q ~ e r t y u i q ~ w e t r y u i q ~ t y u i 160 120 80 40 0 080 60 40 20 100 5 4 3 2 1 0 drain current i ds (ma) duty cycle (%) thermal derating factor characteristics drain-source on-state resistance vs drain current characteristics power dissipation pd (w) ambient temperature ta ( c) 0 25 50 75 85 100 2.0 1.5 1.0 0.5 0 0.764 0.572 0.354 m81016p M81016FP m81016kp 200 160 120 80 40 0 080 60 40 20 100 200 160 120 80 40 0 080 60 40 20 100 200 160 120 80 40 0 080 60 40 20 100 duty cycle-drain current characteristics (m81016p) drain current i ds (ma) duty cycle (%) duty cycle-drain current characteristics (M81016FP) drain current i ds (ma) duty cycle (%) duty cycle-drain current characteristics (M81016FP) drain current i ds (ma) duty cycle (%) ta= 40 c ta=85 c the drain current values represent the current per circuit. repeated frequency 10hz the value the circle represents the value of the simultaneously-operated circuit. ta=85 c drain-source on-state resistance r ds ( on ) ( ? ) the drain current values represent the current per circuit. repeated frequency 10hz the value the circle represents the value of the simultaneously-operated circuit. ta=25 c the drain current values represent the current per circuit. repeated frequency 10hz the value the circle represents the value of the simultaneously-operated circuit. ta=25 c the drain current values represent the current per circuit. repeated frequency 10hz the value the circle represents the value of the simultaneously-operated circuit. ta=85 c
oct.2004 mitsubishi semiconductor m81016p/fp/kp octal d-type flip-flop driver with clear 0 10 20 40 30 50 80 20 40 40 20 100 060 ambient temperature ta ( c ) switching time (ns) drain current i ds (ma) switching time (ns) 10 0 10 1 2 3 5 7 10 2 2 3 5 7 10 3 2 3 5 7 10 1 2 10 2 2 10 3 33 55 77 switching time-drain current characteristics switching time-ambient temperature characteristics t tlh t thl t plh t phl q ~ e y t r u i 200 160 120 80 40 0 080 60 40 20 100 duty cycle-drain current characteristics (m81016kp) drain current i ds (ma) duty cycle (%) q t r e w y i u 200 160 120 80 40 0 080 60 40 20 100 duty cycle-drain current characteristics (m81016kp) drain current i ds (ma) duty cycle (%) r l =240 ? ,v cc =24v,v dd =5v v cc =24v,v dd =5v,ta=25 c t thl t tlh t plh ,t plh(r) t phl the drain current values represent the current per circuit. repeated frequency 10hz the value the circle represents the value of the simultaneously-operated circuit. ta=85 c the drain current values represent the current per circuit. repeated frequency 10hz the value the circle represents the value of the simultaneously-operated circuit. ta=25 c
oct.2004 mitsubishi semiconductor m81016p/fp/kp octal d-type flip-flop driver with clear sdip20-p-300-1.78 weight(g) jedec code 1.0 eiaj package code 20p4b plastic 20pin 300mil sdip symbol min nom max a a 2 b b 1 c e d l dimension in millimeters a 1 0.51 3.3 0.38 0.48 0.58 0.9 1.0 1.3 0.22 0.27 0.34 18.8 19.0 19.2 6.15 6.3 6.45 1.778 ?.62 3.0 0 ?5 4.5 e e 1 20 11 10 1 e c e 1 a 2 a 1 b b 1 e la seating plane d lead material alloy 42/cu alloy sop20-p-300-1.27 weight(g) jedec code 0.26 eiaj package code lead material cu alloy 20p2n-a plastic 20pin 300mil sop symbol min nom max a a 2 b c d e l l 1 y dimension in millimeters h e a 1 i 2 .35 0 0 .18 0 .5 12 .2 5 .5 7 .4 0 .27 1 .1 0 .8 1 .4 0 .2 0 .6 12 .3 5 .27 1 .8 7 .6 0 .25 1 .62 7 .2 0 .1 2 .5 0 .25 0 .7 12 .4 5 .1 8 .8 0 .1 0 b 2 .76 0 0 8 e e 1 20 11 10 1 h e e d e y f a a 2 a 1 l 1 l c e b 2 e 1 i 2 recommended mount pad detail f detail g z z 1 x z 1 0.585 0.735 0.25 z b x m g
oct.2004 mitsubishi semiconductor m81016p/fp/kp octal d-type flip-flop driver with clear ssop20-p-225-0.65 weight(g) jedec code 0.08 eiaj package code lead material alloy 42 20p2e-a plastic 20pin 225mil ssop symbol min nom max a a 2 b c d e l l 1 y dimension in millimeters h e a 1 i 2 .17 0 0 .13 0 .4 6 .3 4 .2 6 .3 0 .0 1 .1 0 .15 1 .22 0 .15 0 .5 6 .4 4 .65 0 .4 6 .5 0 .0 1 .8 5 .2 0 .45 1 .32 0 .2 0 .6 6 .5 4 .6 6 .7 0 .1 0 b 2 .35 0 0 10 e e 1 20 11 10 1 h e e d e y f a a 2 a 1 l 1 l c e b 2 e 1 i 2 recommended mount pad detail f x z 1 0.325 0.475 0.13 z g b x m detail g z z 1
|